Microshift Sword Black 1x9 Groupset

Sword Black 1x9 Groupset offers outstanding entry level value for a performance gravel type bike. This groupset consists of drop-bar Brake levers/shifters, 1 x 9 Rear mech and a wide ratio Cassette. Just add your selection of 1x9 Sword Black cranks, BB and a suitable pair of disc brake calipers to complete your slick shifting entry groupset into performance 1x9 Gravel bike riding. Features Sword Black drop-bar shifters pair modern features with analogue operation. The lever body has a gradually rounded outer edge that’s designed to pair well with flared handlebars, giving you the comfort and control you need even on rough terrain. The brake lever has a higher pivot point and pulls more cable than the average road lever, making your mechanical disc brakes feel stronger and easier to control. The Sword Black 1x rear derailleur features a modern and innovative design with elegant mechanical operation at an exceptional value price. The cage is designed to be used with a single chainring and a wide ratio 9 speed cassette up to 48t. Microshift’s CS-H093, 9 speed cassette is a durable Steel, H-series-Advent type sprocket set for HG-type freehubs, with fast shifting and a smart ED Black finish. The choice of 11-42T or 11-46T 9spd gearing gives a large range of dependable gears at your fingertips.

Stans End Caps - E-Sync/Neo 6 bolt - REAR - 10x135mm Thru Axle (E09 - E10)

These end caps fit 6-bolt E-sync hubs with rare 10x135mm thru-axle spacing (example: DT RWS), and Shimano HG or SRAM XD/XDR cassettes. The non-drive side end cap includes a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Compatible with E-sync, Neo, and Neo Ultimate 6-bolt 10x135mm thru-axle hubs and Shimano HG or SRAM XD/XDR freehubs.

Stans End Caps - E-Sync/Neo 6 bolt - REAR - 10x135mm Thru Axle (E09 - E10)

These end caps fit 6-bolt E-sync hubs with rare 10x135mm thru-axle spacing (example: DT RWS), and Shimano HG or SRAM XD/XDR cassettes. The non-drive side end cap includes a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Compatible with E-sync, Neo, and Neo Ultimate 6-bolt 10x135mm thru-axle hubs and Shimano HG or SRAM XD/XDR freehubs.

Stans Axle - E-Sync / Neo - REAR - 12x135/142 & Singlespeed

This steel rear axle provides maximum durability for E-sync and Neo 135mm, 142mm, and single-speed hubs. With only a 38g weight difference over our standard alloy axle, the steel axle features a high-precision centerless ground treatment that ensures perfect bearing fit. Compatible with E-sync and Neo 6-bolt and Centerlock hubs. Not compatible with 148mm or 157mm E-sync and Neo hubs. Not compatible with M-pulse hubs.

CeramicSpeed UFO Factory Optimized KMC 11S Chain

UFO Factory Optimized KMC 11S Chain Due to its unique optimisation treatment, CeramicSpeed's Ultrafast Racing Chain saves you watts and improves your performance with free speed and unparalleled low friction. Our ultrafast racing chains are carefully selected from high quality suppliers and optimised by hand in Denmark. This ultrafast chain has been optimised for KMC 11-speed compatibility, to boost the efficiency of your entire drivetrain. CeramicSpeed UFO Racing Chains can save you between 2-5 watts on a distance of 650 km/400 miles. Apply CeramicSpeed UFO Drip after 650km to maintain your peak chain optimization over the life of the chain. Be aware that the UFO treatment is not optimised for wet and muddy conditions, which might cause corrosion on the chain. Read more about this in the maintenance tab. Maintenance of UFO Factory Optimized KMC 11S Chain Within 650 km/400 miles, to benefit from the full advantages of the CeramicSpeed UFO Racing Chain, you must not wash the chain before the mileage is exceeded. However, if your chain needs cleaning, use a dry cloth or a soft brush and carefully remove the dirt off the chain. When taking the chain off for maintenance or cleaning, remember to reinstall it in the same direction as before. In the case of a mild shower, where the chain has not been exposed to water more than a few minutes, the chain performance properties should not be affected. In the case of light showers, we recommend applying UFO Drip Chain Coating. Allow the UFO Drip Chain Coating to dry off before riding. In the case of heavy showers, you should cover your chain in a protective grease on top of the UFO treatment. This will slightly influence the watt savings, but it will protect the chain while still improving your performance. After 650 km/400 miles the chain may undergo maintenance, keeping in mind that traces of the optimisation are still left on the chain. When using UFO Drip Chain Coating, after the 650 km/400 miles, please follow the instructions on the bottle. Note that the huge watts saving of 2-5 watts is achieved within the first 650 km/400 miles interval and decrease slightly after the UFO treatment wears off.

CeramicSpeed Single Bearing Coated 61803

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 61903

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 24377

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 61903/18

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 15267

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

DMR Rhythm - Dropout Geared 142mm

DMR Rhythm - Dropout SS QR

DMR Chain Tugs - 10mm - Black

DMR Chain Tugs - 14mm - inc 10mm adp - Black

Surly MDS Dropout

Trek Rear Derailleur Dropouts

DMR Swopout 10mm Horizontal Mk2 Dropout

DMR Swopout Horizontal Mk1.5 Dropout

Identiti S24 ADS Dropout - 10mm

Identiti S24 ADS Dropouts for current ADS Identiti frames.Innovative S-24 ADS option. This tweaked version of the ADS plates, effectively moves the rear axle forwards by a huge 35mm - giving a 26" wheel based frame effectively the same backend as a 24" specific frame, so, NOW you can truly experience 24" specific handling - without the limitation of having to stick with 24" wheels forever... No doubt... others will follow later as they have with our ADS concept...Features: CNC Alloy 6.5mm thick Black anodised Sold Each.

Identiti S24 ADS Dropout - 14mm

Identiti S24 ADS Dropouts for current ADS Identiti frames.Innovative S-24 ADS option. This tweaked version of the ADS plates, effectively moves the rear axle forwards by a huge 35mm - giving a 26" wheel based frame effectively the same backend as a 24" specific frame, so, NOW you can truly experience 24" specific handling - without the limitation of having to stick with 24" wheels forever... No doubt... others will follow later as they have with our ADS concept...Features: CNC Alloy 6.5mm thick Black anodised Sold Each

Identiti Jekyll/Hyde/666 ADS Dropout

Features: Identiti Alloy ADS Dropouts for current ADS Identiti frames CNC Alloy 6.5mm thick Black anodised Sold Each

Identiti Rohloff ADS Dropout

Rohloff Speedhub dropouts for current ADS Identiti frames.Tweaked version of the original ADS dropouts - with a reinforced longer Left hand jaw to accept Rohloff OEM axle plates and a neat non-hanger Right hand jaw. This set allows you to fit a Rohloff Speedhub in conjuction with Rohloff OEM axle plates - therefore avoiding the need to use Torque arms or Speed bones. Thus creating a VERY neat and economic Speedhub set-up. Rohloff ADS plates are compatible with all current Identiti ADS frames.