CeramicSpeed Wheel Bearing Press Tool Kit

Hidden CeramicSpeed bearing inside tool head for smooth function and reduced effort. Innovative Quick Release mechanism in tool head saves time. Premium steel punch included for hub designs incompatible with overcup extraction methods. Nesting drift design compatible with captive axel and removeable axel hubs. End-cap removal tool to aid removal of pressfit end caps that may become stuck or difficult to remove. Developed and designed in Denmark.

CeramicSpeed UFO Factory Optimized KMC 11S Chain

UFO Factory Optimized KMC 11S Chain Due to its unique optimisation treatment, CeramicSpeed's Ultrafast Racing Chain saves you watts and improves your performance with free speed and unparalleled low friction. Our ultrafast racing chains are carefully selected from high quality suppliers and optimised by hand in Denmark. This ultrafast chain has been optimised for KMC 11-speed compatibility, to boost the efficiency of your entire drivetrain. CeramicSpeed UFO Racing Chains can save you between 2-5 watts on a distance of 650 km/400 miles. Apply CeramicSpeed UFO Drip after 650km to maintain your peak chain optimization over the life of the chain. Be aware that the UFO treatment is not optimised for wet and muddy conditions, which might cause corrosion on the chain. Read more about this in the maintenance tab. Maintenance of UFO Factory Optimized KMC 11S Chain Within 650 km/400 miles, to benefit from the full advantages of the CeramicSpeed UFO Racing Chain, you must not wash the chain before the mileage is exceeded. However, if your chain needs cleaning, use a dry cloth or a soft brush and carefully remove the dirt off the chain. When taking the chain off for maintenance or cleaning, remember to reinstall it in the same direction as before. In the case of a mild shower, where the chain has not been exposed to water more than a few minutes, the chain performance properties should not be affected. In the case of light showers, we recommend applying UFO Drip Chain Coating. Allow the UFO Drip Chain Coating to dry off before riding. In the case of heavy showers, you should cover your chain in a protective grease on top of the UFO treatment. This will slightly influence the watt savings, but it will protect the chain while still improving your performance. After 650 km/400 miles the chain may undergo maintenance, keeping in mind that traces of the optimisation are still left on the chain. When using UFO Drip Chain Coating, after the 650 km/400 miles, please follow the instructions on the bottle. Note that the huge watts saving of 2-5 watts is achieved within the first 650 km/400 miles interval and decrease slightly after the UFO treatment wears off.

CeramicSpeed UFO Wet Weather Essentials Bundle

The UFO Wet Weather Essentials Bundle is tailored to riders who consistently ride in wet conditions or off the tarmac. Keep your drivetrain optimized and protected in the most challenging terrains and conditions.   Show your bike how much you care!  

CeramicSpeed UFO Bearings Race Day Grease

UFO Bearings Race Day Grease Is designed to deliver as low friction as possible, thanks to the Dynamic Viscosity Transformation (DVT) technology that applies as a foamy grease and changes to a lubricating oil film under pressure. 30ml.

CeramicSpeed BSA T45 and T4786 30mm Service Kit

Crank Compatibility: 30m Frame/cup: BSA30. T45 (Colnago). T47-86mm. In the box: 2 bearing seals. 2 bearing dust covers. 1 x O-ring. 2 x 1mm spacers. 2 x 0,5mm spacer. 5ml CeramicSpeed All Round Grease.  

CeramicSpeed Threaded, and PF46mm Cup Shimano Service Kit

Crank Compatibility: Shimano / 24mm spindle Frame/cup: PF30. PF30a. BBright. EVO386. BSA. ITA. T45. T47-68mm. T47-86mm.

CeramicSpeed ITA for DUB Service Kit

Frame/cup: ITA In the box: 2 bearing seals. 2 bearing dust covers. 4 x 1mm spacers. 3 x 3mm spacer. 5ml CeramicSpeed All Round Grease.  

CeramicSpeed 30mm Threaded and 386Evo SRAM DUB Service Kit

Riders with a BSA, T4530, T4730 Bottom Bracket, or if they have a PF4630 on an EVO386 frame, can utilize this kit to install a DUB crank. Crank Compatibility: SRAM DUB Frame/Cup: BB30. PF30. PF30a. BBright. EVO386. BSA. T45. T47-68mm. T47-86mm.

CeramicSpeed OSPW System Cerakote Coated Campag 12 spd Pulley Wheels

OSPW for Campagnolo 12-speed EPS Cerakote Limited Edition The OSPW System for Campagnolo 12-speed EPS comes with a compact moulded carbon fibre cage for light weight and durability. The system offers a three spring tension setting that allows for optimal setup based on riding conditions. Like every other CeramicSpeed Oversized Pulley Wheel System, this is developed, designed and handbuilt in Denmark. The product comes with unique ceramic coated pulleys in Pink and White Cerakoate with a lifetime warranty. The system is not compatible with 12-speed mechanical.  

CeramicSpeed OHD SLT Headset Bearing SS 1.1/4" 35 x 47 x 7mm 36/45°

The CeramicSpeed SLT (Solid Lubrication Technology) Bearing for Headsets: OHD (Optimized Headset Design), features a unique combination of an oil-encapsulated solid plastic polymer and stainless-steel materials which results in a self-lubricating, corrosion-resistant, and maintenance-free bearing. The micropores in the otherwise solid polymer evenly distribute just enough oil to keep the bearing well-lubricated, while also containing sufficient oil for it to be self-lubricating over the lifespan of the bearing – even when ridden in the harshest of conditions. The CeramicSpeed SLT OHD Bearing is designed, developed, and hand-built in Denmark and comes with a lifetime warranty.  

CeramicSpeed Single Bearing Coated 61803

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 61903

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed BB Seal and Dust Cover Service Tool

Unique multifunction tool provides an easy and clever way to remove secure fitting integrated dust covers, as well as assisting in alignment and simple installation of bearing seals and/or dust cover reinstallation. Supports easy dust cover removal and installation of seals and dust covers. Integrated Shimano crank preload tool. Compatible with CeramicSpeed dust covers and seals for Shimano 24mm bottom brackets, CeramicSpeed dust covers and seals for DUB 28.99mm bottom brackets, plus reinstallation of 30mm bearing seals. For road or off-road use.  

CeramicSpeed BB86/92 DUB Service Kit

Riders with the new PF4130 design can use this kit to install a DUB crank. It is important to note that the inner race must be recessed roughly 2.8mm to provide clearance for the dust cover. this is the key change on the new PF4130 that began shipping in 2018. if the inner race (and seal) are flush with the outer race the Bottom Bracket cannot be converted for use with DUB cranks. Crank Compatibility: SRAM DUB Frame/Cup: BB86

CeramicSpeed Preload Bolt for Shimano cranks

Replaces the plastic OE preload bolt on 24mm Shimano cranks.

CeramicSpeed Single Bearing Coated 24377

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 61903/18

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed OHD SLT Headset Bearing Kit Colnago G3X

The CeramicSpeed SLT (Solid Lubrication Technology) Bearing for Headsets: OHD (Optimized Headset Design), features a unique combination of an oil-encapsulated solid plastic polymer and stainless-steel materials which results in a self-lubricating, corrosion-resistant, and maintenance-free bearing. The micropores in the otherwise solid polymer evenly distribute just enough oil to keep the bearing well-lubricated, while also containing sufficient oil for it to be self-lubricating over the lifespan of the bearing – even when ridden in the harshest of conditions. The CeramicSpeed SLT OHD Bearing is designed, developed, and hand-built in Denmark and comes with a lifetime warranty. For more information about CeramicSpeed SLT bearings click here This kit contains 1 x 110942 and 1 x 110940 bearings.

CeramicSpeed Headset Bearings for Specialized Headset 5 Shiv Tri

CeramicSpeed headset bearings will take your handling of your bike to new levels, our bearings are built by hand in Denmark to ensure the highest performance and longevity. Specialized Headset 5 comes in two variants, with our CeramicSpeed Standard Bearings and with out Coated Bearings.The Coated Bearings offer an even longer lifetime and lower friction. Learn more about the coated advantage here

CeramicSpeed Single Bearing Coated 15267

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed ITA SRAM DUB Coated Bottom Bracket

CeramicSpeed BB86 CAMPY UT Bearing Kit Bottom Bracket