CeramicSpeed UFO Hot Wax Chain Hanger

CeramicSpeed UFO Wax Ultra Endurance Kit

CeramicSpeed UFO Wax Ultra Endurance Bag

CeramicSpeed UFO Ultimate Bike Care Bundle

CeramicSpeed UFO Speed Chain SRAM 12S Flattop

CeramicSpeed UFO Factory Optimized KMC 12S Chain

UFO Factory Optimized KMC 12S Chain Due to its unique optimisation treatment, CeramicSpeed's Ultrafast Racing Chain saves you watts and improves your performance with free speed and unparalleled low friction. Our ultrafast racing chains are carefully selected from high quality suppliers and optimised by hand in Denmark. CeramicSpeed UFO Racing Chains can save you between 2–5 watts on a distance of 650 km/400 miles. Apply CeramicSpeed UFO Drip after 650km to maintain your peak chain optimization over the life of the chain. Be aware that the UFO treatment is not optimised for wet and muddy conditions, which might cause corrosion on the chain. In The Box 126 link Optimized Chain. Quick Link. Disposable Gloves. Sticker Sheet. Single-use UFO Drip Sample.

CeramicSpeed UFO Factory Optimized KMC 11S Chain

UFO Factory Optimized KMC 11S Chain Due to its unique optimisation treatment, CeramicSpeed's Ultrafast Racing Chain saves you watts and improves your performance with free speed and unparalleled low friction. Our ultrafast racing chains are carefully selected from high quality suppliers and optimised by hand in Denmark. This ultrafast chain has been optimised for KMC 11-speed compatibility, to boost the efficiency of your entire drivetrain. CeramicSpeed UFO Racing Chains can save you between 2-5 watts on a distance of 650 km/400 miles. Apply CeramicSpeed UFO Drip after 650km to maintain your peak chain optimization over the life of the chain. Be aware that the UFO treatment is not optimised for wet and muddy conditions, which might cause corrosion on the chain. Read more about this in the maintenance tab. Maintenance of UFO Factory Optimized KMC 11S Chain Within 650 km/400 miles, to benefit from the full advantages of the CeramicSpeed UFO Racing Chain, you must not wash the chain before the mileage is exceeded. However, if your chain needs cleaning, use a dry cloth or a soft brush and carefully remove the dirt off the chain. When taking the chain off for maintenance or cleaning, remember to reinstall it in the same direction as before. In the case of a mild shower, where the chain has not been exposed to water more than a few minutes, the chain performance properties should not be affected. In the case of light showers, we recommend applying UFO Drip Chain Coating. Allow the UFO Drip Chain Coating to dry off before riding. In the case of heavy showers, you should cover your chain in a protective grease on top of the UFO treatment. This will slightly influence the watt savings, but it will protect the chain while still improving your performance. After 650 km/400 miles the chain may undergo maintenance, keeping in mind that traces of the optimisation are still left on the chain. When using UFO Drip Chain Coating, after the 650 km/400 miles, please follow the instructions on the bottle. Note that the huge watts saving of 2-5 watts is achieved within the first 650 km/400 miles interval and decrease slightly after the UFO treatment wears off.

CeramicSpeed Single Bearing Coated 61803

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 61903

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 24377

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 61903/18

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing Coated 15267

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

CeramicSpeed Single Bearing R8

CeramicSpeed Single Bearing Coated 61802 (6802)

CeramicSpeed Single Bearing Coated 61801 (6801)

CeramicSpeed Single Bearing Coated 608

CeramicSpeed Single Bearing Coated 6001

CeramicSpeed Single Bearing 61903/18

CeramicSpeed Single Bearing 61903 (6903)

CeramicSpeed Single Bearing 61902 (6902)

CeramicSpeed Single Bearing 61806 (6806)

CeramicSpeed Single Bearing 61803 (6803)

CeramicSpeed Single Bearing 15267